MSE-6 Mouse Droid Build

Ask about costumes and props here. Please read the FAQs first before asking questions -- your question may have already been answered!
Sleg
GLG Member
GLG Member
Posts: 2382
Joined: Wed May 30, 2007 9:09 am
Legion ID: 9317
Location: Monroe, Michigan

MSE-6 Mouse Droid Build

Post by Sleg »

Just about finished with my MSE-6 Mouse Droid.

I figured I would post up some pics for anyone considering building one.
Open some dialog on specs, reference pics, methods, and such.

So far it has been a pretty easy build, cheap, and it is a nice little project that one could involve the kid(s) in for a little Master/Padawn bonding.

I started with a 1:12 scale RC car from Toys R Us.
Most people use the 1:10 scale as it was the original size used in the movie(s).

Stripped it down and basically had a RC chassis.

I started with a mock up build using US Postal Boxes.
They are free*, light weight but sturdy.
*you are suppose to use these for mail only so please follow the rules.... :wink:

Started with the bottom panels/frame and modified as I went forward to get the correct looking proportions for the top shell.

Image

Image

Image

Image

Image

Started to come together so that I could get a sense if it looked close to the original in size and angles.

Image

Image
TK/DZ/BH/TS -9317
501st Legion
Great Lakes Garrison

R2 Builder Club
Sleg
GLG Member
GLG Member
Posts: 2382
Joined: Wed May 30, 2007 9:09 am
Legion ID: 9317
Location: Monroe, Michigan

Re: MSE-6 Mouse Droid Build

Post by Sleg »

I moved up to a stronger material for the next mock build up.
I put it together with ruff seams with no mitering the joints.
Turned out a bit ruff, but it was really sturdy.
Enough so that I was actually going to stick with this as the final product at first.

I used foam display board. The kind a kid will use for a science fair project. When hot glued and reinforced this stuff is actually pretty strong.
Plus it made the droid extremely light and fast.

Base
Image

Image

Glued up the seams with Hot Glue
Image

Image

Cut out the hubs for steering.
Image

Now the shell....
Image

Image

Image

Image

Other than the joints, it turned out pretty nice and it was really sturdy strong so I decided that I would stay with this material for the shell.

After running around the house for a minute I ran into the fridge and put a huge dent into the front edges. I would have to reinforce the front and rear with some type of bumper to prevent that.

But first, I worked on the droid sides and the antenna arrays that sit on top.
TK/DZ/BH/TS -9317
501st Legion
Great Lakes Garrison

R2 Builder Club
Sleg
GLG Member
GLG Member
Posts: 2382
Joined: Wed May 30, 2007 9:09 am
Legion ID: 9317
Location: Monroe, Michigan

Re: MSE-6 Mouse Droid Build

Post by Sleg »

Here are some of the reference pic I used to match up with the screen used droid.

Image

Image

Image

For the sides.
Circuit Board from Radio Shack cut to size.
A lot of 14 pin DIP IC Sockets Adaptor and 14 pin General Purpose Dual Bipolar Timers.

Image

Image

Image

Image

Here they are finished and glued into place.
Image

Image

Other side....
Image

Now the arrays.
Basically found a bunch of stuff at work and around the house that looked radio antenna'ish.

Image
That might be the only pic...CRAP!

Anyway, here they are installed.
Image

Image

Image

Up next....Paint and Sound.
TK/DZ/BH/TS -9317
501st Legion
Great Lakes Garrison

R2 Builder Club
User avatar
Mira_Darkstar
GLG Member
GLG Member
Posts: 761
Joined: Tue Jun 01, 2010 3:44 pm
Location: Lansing, MI

Re: MSE-6 Mouse Droid Build

Post by Mira_Darkstar »

Looks fantastic so far!
Costumes: Mara Jade, Slave Leia, and Rey.
User avatar
Hyper
GLG Member
GLG Member
Posts: 1375
Joined: Sun May 04, 2008 4:48 pm
Legion ID: 4408

Re: MSE-6 Mouse Droid Build

Post by Hyper »

So cool

You are a very talented craftsman
User avatar
Flash
Garrison Advisor
Garrison Advisor
Posts: 4797
Joined: Sat Jun 05, 2010 10:25 pm
Legion ID: 5156

Re: MSE-6 Mouse Droid Build

Post by Flash »

That thing looks great. Good Job Jerry.
Mike Lica - 5156
I like Star Wars
tk1440
GLG Member
GLG Member
Posts: 652
Joined: Sun Sep 10, 2006 10:21 pm
Legion ID: 1440

Re: MSE-6 Mouse Droid Build

Post by tk1440 »

Look realy nice can't wait to see at MCCC :thumbs:

Rich
1440
User avatar
Lumpy
GLG Member
GLG Member
Posts: 7842
Joined: Sat Aug 23, 2008 9:28 am
Legion ID: 7189
Location: Kashyyyk

Re: MSE-6 Mouse Droid Build

Post by Lumpy »

Do I get to Wookiee roar at it??? :mrgreen:
Sleg
GLG Member
GLG Member
Posts: 2382
Joined: Wed May 30, 2007 9:09 am
Legion ID: 9317
Location: Monroe, Michigan

Re: MSE-6 Mouse Droid Build

Post by Sleg »

Lumpy wrote:Do I get to Wookiee roar at it??? :mrgreen:
Sure thing Chris!

And I have a Wookiee roar in the audio loop for when you're not around too. :thumbs:
TK/DZ/BH/TS -9317
501st Legion
Great Lakes Garrison

R2 Builder Club
Sleg
GLG Member
GLG Member
Posts: 2382
Joined: Wed May 30, 2007 9:09 am
Legion ID: 9317
Location: Monroe, Michigan

Re: MSE-6 Mouse Droid Build

Post by Sleg »

Mira_Darkstar wrote:Looks fantastic so far!
Hyper wrote:So cool - You are a very talented craftsman
Flash wrote:That thing looks great. Good Job Jerry.
tk1440 wrote:Look realy nice can't wait to see at MCCC :thumbs:
Thanks guys!
TK/DZ/BH/TS -9317
501st Legion
Great Lakes Garrison

R2 Builder Club
Sleg
GLG Member
GLG Member
Posts: 2382
Joined: Wed May 30, 2007 9:09 am
Legion ID: 9317
Location: Monroe, Michigan

Re: MSE-6 Mouse Droid Build

Post by Sleg »

I actually shot the paint on this thing last week and the results - not good.

I used a water based spray since I was concerned that the regular spray paint would melt the edge of the foam board leaving it pitted. Turns out the foam did not pit or melt, but the paper surface absorbed too much of the "water" in places loosening the glue and it pulled away from the foam core.

I had to start over with the body/shell. :mad:
TK/DZ/BH/TS -9317
501st Legion
Great Lakes Garrison

R2 Builder Club
User avatar
Myshadowstar
GLG Member (Reserve)
GLG Member (Reserve)
Posts: 677
Joined: Thu Aug 12, 2010 6:38 pm
Legion ID: 7957
Location: Southgate, MI
Contact:

Re: MSE-6 Mouse Droid Build

Post by Myshadowstar »

wow other than that setback everything's looking awesome cant wait to see the completed project! :thumbs: :mrgreen:
"Only the Shadow knows what evil lurks in the hearts of men..."

Myshadowstar

------------
Old Republic Jedi- complete
Imperial Officer- complete

Image
User avatar
Wags
Garrison Armor Consultant
Garrison Armor Consultant
Posts: 2850
Joined: Thu Jun 14, 2007 12:32 am
Legion ID: 7195
Location: Allen Park, Mi 48101

Re: MSE-6 Mouse Droid Build

Post by Wags »

Jerry, I have a bunch of styrene if you need it. Just let me know!! :thumbs:
Sleg
GLG Member
GLG Member
Posts: 2382
Joined: Wed May 30, 2007 9:09 am
Legion ID: 9317
Location: Monroe, Michigan

Re: MSE-6 Mouse Droid Build

Post by Sleg »

Thanks for the offer Wages!

I actually found some of the same foam board but this time with a laminated skin and it comes in several thicknesses.
Bought some to test the paint and it worked fine!

I will post up some progress pics later tonight. :thumbs:
TK/DZ/BH/TS -9317
501st Legion
Great Lakes Garrison

R2 Builder Club
Sleg
GLG Member
GLG Member
Posts: 2382
Joined: Wed May 30, 2007 9:09 am
Legion ID: 9317
Location: Monroe, Michigan

Re: MSE-6 Mouse Droid Build

Post by Sleg »

New shell and base.
I mitered all the joints for a clean look.
Used some material from Mike Lika (thanks Mike) to cover the ends of the exposed foam core and it worked perfectly.
Image

Image

Image

Image

Reinstalled the sides
Image

Sound
Image

Image

Image

Image

Image

Arrays installed
Image

Image
This thing is like a rolling juke box.
I have a lot of mouse droid sounds, audio from Episode IV, and some funny stuff too running on a loop.

Possible driver?
Image


I will install the cooling fins that run along the side panels and shoot the paint tomorrow.

Later -

Jerry
TK/DZ/BH/TS -9317
501st Legion
Great Lakes Garrison

R2 Builder Club
User avatar
Flash
Garrison Advisor
Garrison Advisor
Posts: 4797
Joined: Sat Jun 05, 2010 10:25 pm
Legion ID: 5156

Re: MSE-6 Mouse Droid Build

Post by Flash »

I can't wait to see it in person, or in droid........ :thumbs:
Mike Lica - 5156
I like Star Wars
User avatar
Keanu
GLG Member (Reserve)
GLG Member (Reserve)
Posts: 117
Joined: Sat Sep 23, 2006 9:42 pm
Legion ID: 7088
Location: ann arbor, mi

Re: MSE-6 Mouse Droid Build

Post by Keanu »

That's pretty slick; very resourceful. Look forward to seeing this in action.
Sleg
GLG Member
GLG Member
Posts: 2382
Joined: Wed May 30, 2007 9:09 am
Legion ID: 9317
Location: Monroe, Michigan

Re: MSE-6 Mouse Droid Build

Post by Sleg »

Done!!!

Image

Image

Image

Image

Image

Here is a short video.
I have a trial audio loop running.
Zane's dog Max does not care for the MSE at all.
Got to love the timing of the Wookiee growl after he barks at the droid!

Full version on YouTube
TK/DZ/BH/TS -9317
501st Legion
Great Lakes Garrison

R2 Builder Club
User avatar
Flash
Garrison Advisor
Garrison Advisor
Posts: 4797
Joined: Sat Jun 05, 2010 10:25 pm
Legion ID: 5156

Re: MSE-6 Mouse Droid Build

Post by Flash »

That is the coolest thing I have seen in a long time. :thumbs:
Mike Lica - 5156
I like Star Wars
User avatar
Thumper
GLG Member
GLG Member
Posts: 1672
Joined: Tue May 03, 2005 7:07 pm
Legion ID: 1148

Re: MSE-6 Mouse Droid Build

Post by Thumper »

:blink: I WANT ONE!!!!!

THAT IS UBER AWESOME!!


Way to go Jerry!!!
Brooke Merva
TD 1148
Great Lakes Garrison
Post Reply